新聞資訊
網站首頁 > 新聞資訊 >

安裝操作站報警如何判斷?還需要進行哪些操作?

2020-10-28 10:50:29 來源:http://www.qistar-garment.net/ 53

操作站報警如何判斷?
How to judge the alarm of operation station?
通常情況下,引起操作站故障的原因主要有兩類:硬件故障和軟件故障。下麵分別介紹各種故障原因及處理方法。如果死機重啟後無法進入操作係統界麵,丝瓜视频免费下ioses幸福宝先聽計算機啟動時的提示音,按提示音初步判斷故障所在,並先予以解決。如果提示音正常而無法進入windows界麵,則應是windows文件有錯誤,需要重新安裝操作係統。
In general, there are two main causes of the operation station failure: hardware failure and software failure. The following describes the causes of various failures and treatment methods. If you can't enter the interface of the operating system after the crash and restart, we first listen to the prompt tone when the computer starts, and then preliminarily judge the fault according to the prompt tone, and solve the problem first. If the prompt tone is normal and the windows interface cannot be accessed, the windows file is wrong and the operating system needs to be re installed.
     浙大中控
windows文件錯誤的產生可能是硬盤有壞磁道引起,需要先用windows98的啟動盤啟動後,在命令提示符下輸入scandisk c:對硬盤的主分區進行掃描,確認硬盤沒有故障的情況後,對操作係統重新進行安裝;如果硬盤有故障,建議更換硬盤再重新安裝windows操作係統。如果死機重啟後可以進入操作係統界麵,但間隔一段時間後,又會重新死機則需要分析軟硬件的其它可能性。
Windows file errors may be caused by bad tracks in the hard disk. You need to start with Windows 98 boot disk, and then enter ScanDisk C at the command prompt to scan the main partition of the hard disk. After confirming that the hard disk is not faulty, the operating system is reinstalled. If the hard disk fails, it is recommended to replace the hard disk and then re install the windows operating system. If you can enter the operating system interface after a crash and restart, but it will crash again after a period of time, then you need to analyze other possibilities of software and hardware.
安裝完操作係統後還需要進行哪些操作?
What else do you need to do after installing the operating system?
A:1、安裝主板、顯卡、聲卡、網卡等驅動
A: 1. Install the main board, graphics card, sound card, network card and other drivers
2、安裝組態軟件
2. Install configuration software
3、進行IP地址設置(根據網卡數量及操作站地址設置)
3. Set IP address (according to the number of network cards and the address of operation station)
4、關閉網卡流控製
4. Turn off NIC flow control
5、連接網絡,進行組態或監控運行
5. Connect the network for configuration or monitoring operation
以上是關於浙大中控操作站報警如何判斷的介紹,希望對大家有所幫助,如想了解更多內容歡迎點擊http://www.qistar-garment.net網站。
The above is about Zhejiang University central control operation station alarm how to judge, hope to help you, if you want to know more content, welcome to click http://www.qistar-garment.net Website.
產品推薦
新聞推薦